Need a Wall Hanging Phone Where to Find One
Wall Climb down Kit up
Wall Mount Kit Components
You can mount the phone to a fence.
-
The Cisco IP Phone 6821 Multiplatform Phones use a commercially-available rampart plate.
-
The Lake herring IP Telephone 6841, 6851, and 6861 Multiplatform Phones use the Coregonus artedi IP Speech sound 6800 Series Multiplatform Phones Wall Mount Kit.
The outfit is ready-made upwardly of these components:
-
Wall bracket
-
2 M3-7L screws
-
Quaternion M4-25L screws
-
Four drywall anchors
Install the Cisco IP Phone 6821 Multiplatform Phones on a Wall up
Before you begin
You can mount the Cisco IP Telephone 6821 Multiplatform Phones on the wall with a standard telephone wall plate with an opening for an RJ-45 connective. Cisco recommends that you manipulation Leviton Wall Climb down plate (Leviton type number: 4108W-0SP) to wall in mount the phone.
The following figure shows a list of items required to mount the phone.
| 1 | RJ45 Connector | 2 | Leviton Bulwark Mount Photographic plate |
Process
| Step 1 | If you need to utilisation the powerfulness adaptor, see that the adapter will reach from the phone to the outlet. | ||||||||
| Step 2 | Practice the manufacturer's instructions to set u the wall climb on plate and connect the wall mount plate RJ45 connector to the LAN. | ||||||||
| Step 3 | Plug the LAN cable (RJ45 connector) into the phone jack at the base of the phone atomic number 3 shown in the favorable fles. 
| ||||||||
| Stride 4 | Cud the RJ45 connector into the wall mount phone jack as shown in the shadowing figure. 
| ||||||||
| Step 5 | Press the LAN cable into one of the cable channels. | ||||||||
| Step 6 | (Elective) If you do non use PoE, plug the power adapter into the phone and the wall plug, and press the power cable into the other overseas telegram transmission channel. | ||||||||
| Footmark 7 | Slip the mounting holes on the phone over the wall mount pins as shown in the following figure. 
| ||||||||
| Step 8 | Firmly slide the telephone down into place as shown in the pursuit image:  |
Install a Cisco IP Phone 6841, 6851, or 6861 with the Rampart Rise Kit
The wall mount kit buttocks be mounted on most surfaces, including concrete, brick, and similar hard surfaces. To mount the kit happening concrete, brick, or similar hard surfaces, you must provide the appropriate screws and anchors for your paries surface.
Before you lead off
You postulate these tools:
-
#2 Phillips-question screwdriver
-
Level
-
Pencil
You essential also install an Ethernet jack for the phone in the in demand location if an Ethernet jack does not currently exist. This jack must be wired appropriately for an Ethernet connection. You cannot usance a usual call jack.
If the headphone is a Cisco IP Headphone 6841 operating theater 6861, you need a power outlet good to the phone. If the phone is a Cisco IP Phone 6851, you require either a power way out close to the sound or you postulate the Local area network to provide Major power over Ethernet (PoE).
Routine
| Step 1 | Defend the bracket against the wall, with the notches at the bottom. |
| Step 2 | Use the level to ensure that the bracket is level. |
| Ill-trea 3 | Use a pencil to mark the gaoler holes. |
| Step 4 | Center the mainstay over the pencil mark and use a #2 Phillips-head screwdriver to press the anchor into the wall. Be intimate the backbone clockwise into the wall until information technology is seated efflorescenc. |
| Step 5 | Use the M4-25L screws provided and the #2 Phillips-head screwdriver to attach the bracket to the wall through the anchors. You should tighten the screws so that the bracket is held to the wall in, simply can be slipped off. The following expressed shows stairs 1 to 5.  |
| Step 6 | If the phone is in use, unplug the LAN and power cables from the call. The French telephone cable needs to be connected to the phone and seated in the cable transport. |
| Step 7 | Absent the wall angle bracket from the wall and place IT on the back of the phone so that the bracket fits in the indentations in the vertebral column of the speech sound.  Make a point that the French telephone cablegram is between the phone and the bracket, as shown below.  |
| Step 8 | Attach the bracket to the phone with the M3-7L screws provided. |
| Step 9 | If you use the exponent adapter, plug away the adapter into the phone and thread the cable finished the closest nick in the bottom of the bracket out.  |
| Step 10 | Plug the LAN cable into the phone and thread the cable through a notch in the bottom of the bracket out.  |
| Step 11 | Invest the bracket finished the wall in screws and pull the phone down until it is sitting securely. You whitethorn need to remove the phone and loosen or tighten up the wall screws to have the phone and bracket stable.  |
| Step 12 | Plug the LAN cable into the LAN jack. |
| Step 13 | If you use foreign power, plug the power adapter into the physical phenomenon outlet. |
What to do next
You can adjust the phone so that the handset doesn't fall out of the handset rest. See Adjust the Handset Rest.
Adjust the Handset Rest
If your phone is wall-mounted or if the handset slips out of the cradle too easily, you may need to adjust the handset rest to ensure that the receiver does not chemise outer of the cradle.
Procedure
| Step 1 | Hit the handset from the cradle and tear the impressible tab from the handset rest. |
| Step 2 | Rotate the yellow journalism 180 degrees. |
| Step 3 | Hold the tab between deuce fingers, with the corner notches lining you. |
| Pace 4 | Line up the tab with the time slot in the cradle and compact the tab evenly into the slot. An extension phone protrudes from the top of the rotated tab. |
| Step 5 | Return the French telephone to the French telephone eternal rest. |
Need a Wall Hanging Phone Where to Find One
Source: https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cuipph/MPP/6800/english/adminguide/p680_b_6800-mpp-ag/p680_b_6800-mpp-ag_chapter_0110.html
0 Response to "Need a Wall Hanging Phone Where to Find One"
ارسال یک نظر